Important knowledge of new dry process cement - Three

Jul 17, 2025

Leave a message

 

Important knowledge of new dry process cement

 

Suspension Preheating Technology

 

 

Connotation of Suspension Preheating Technology:

Suspension preheating technology refers to the process where low-temperature powder material is uniformly dispersed in a high-temperature airflow. Heat exchange occurs in suspension, enabling the material to be rapidly heated and warmed.

 

Cyclone Function and Principle:

A. Function: To complete the separation of gas and solid phases, and to collect solid raw material powder.

B. Principle: The airflow carries the raw material powder tangentially at high speed into the cyclone, forcing it to rotate inside the cylindrical body and exhaust pipe. While rotating, the material moves downward through the cylinder to the bottom, then is reflected upward and discharged through the exhaust pipe. In this way, the raw material heated by the previous preheating unit is separated in the cyclone before entering the next heat exchange unit to continue heating and warming.

 

Optimization and Improvement of New Cyclone Structure:

Various measures have been taken around the cyclone to reduce the airflow rotational speed, shorten ineffective airflow strokes within the cyclone, minimize collisions between inlet airflow and return flow, and reduce unnecessary churning, thereby lowering cyclone resistance. Common measures include:

① Adding a blocking-type deflector

② Installing an eccentric inner tube, flat round inner tube, or "boot-shaped" inner tube

③ Using a large spiral inlet structure inside the cyclone shell

④ Appropriately reducing the air inlet velocity

⑤ Shaping the bottom of the cyclone shell into a sloping surface

⑥ Using a tilted inlet and lid structure for the cyclone

⑦ Increasing the area of the inner tube

⑧ Shortening the insertion depth of the inner tube

⑨ Appropriately increasing the cyclone height-to-diameter ratio

⑩ Installing an expansion bin at the bottom of the cyclone

 

Cyclone Inlet Form and Structure

A: There are generally two types of cyclone inlets: one where the outer edge of the inlet airflow is tangent to the cylinder (straight-in type), and another where the inner edge of the airflow is tangent to the cylinder (spiral shell type). Most new cyclone shells have inlet angles divided into three forms: 90°, 180°, and 270°.

Structure: Most traditional cyclone inlets have a rectangular shape, with inlet wind speeds generally in the range of 15 to 25 m/s. The new cyclone inlets have been improved to pentagonal or rhombic structures.

 

Role and Structure of the Material Spreading Device in the Heat Exchanger Pipe

A: Role: The material spreading device prevents downstream material from entering the heat exchanger pipeline directly. It promotes the material to splash and disperse onto the downstream material plates. This ensures effective heat transfer between the gas phase, solid phase, and the two-phase mixture inside the heat transfer pipeline. There are two main structural types: plate spreaders and spreading boxes.

 

Role and Structure of the Locking Flap Ash Valve in the Heat Exchanger Pipe

A: The locking flap ash valve maintains a sealed state in the downstream pipeline. It helps to keep the material flow uniform and smooth, and prevents the downstream pipeline space from being filled with material. This minimizes the risk of airflow short circuits and leakage caused by pressure differences between the upper-level and lower-level cyclones and the heat exchanger pipeline outlet. It ensures that in the heat exchanger pipeline, gas and material flow separately ("gas goes its way, material goes its way").

This not only prevents hot air from flowing upward through the lower tube to the upper cyclone inlet - which would cause materials to be re-entrained and reduce separation efficiency - but also stops hot air from bypassing heat exchange by entering the cyclone from the upper-level bottom, which leads to unnecessary heat loss and lower heat transfer efficiency.

There are generally three structural forms of the locking flap ash valve: single-plate type, double-plate type, and flap type.

 

Pre-Decomposition Technology

 

 

Pre-decomposition technology refers to the process in which cement raw materials, after suspension preheating but before reaching the decomposition temperature, are introduced into a decomposition furnace. In the furnace, the raw materials mix with fuel in a suspended state and rapidly absorb the combustion heat, enabling the calcium carbonate in the raw material to quickly decompose into calcium oxide.

 

 

Features of the Pre-Decomposition Kiln:

A decomposition furnace is added between the suspension preheater and the rotary kiln, allowing the exothermic combustion of the fuel and the decomposition of the raw material carbonate to occur rapidly in a suspended state. Both the heat release from fuel combustion and the heat absorption for carbonate decomposition happen very quickly in suspension.

 

Gas and Solid Flow Movement and Function in the Decomposition Furnace:

A: The air movement inside the decomposition furnace generally takes four basic forms: vortex, ejector, suspension, and fluidized bed. In these forms, raw materials and fuels are dispersed in the airflow by vortex effect, ejector effect, suspension, or fluidized bed effect, respectively. Due to the relative motion between the materials within the furnace flow field, a high degree of dispersion, homogeneous mixing, and distribution is achieved, promoting rapid heat transfer and prolonging the retention time of materials in the furnace. This improves combustion efficiency, heat transfer efficiency, and the carbonate decomposition rate of the materials before entering the kiln.

 

Measures to Prevent Crusting

A. Reduce or avoid the use of raw materials with high chlorine and high sulfur content.

B. Use coal with low chlorine and low or medium sulfur content.

C. If excessive chlorine and sulfur are unavoidable, it is recommended to adopt the following measures:

 ① Discard a portion of the kiln ash to reduce the chlorine cycle.

 ② Implement a bypass air release system.

D. Avoid using coal with high ash content and a low ash melting point.

E. Carefully operate the kiln and preheater to ensure stable temperatures, pressures, and feed quantities throughout the system.

 

Causes of Bonding Blockage Failure in the Pre-Decomposition Kiln System:

① The volatility coefficients of potassium, sodium, and sulfur in the materials, especially under reducing atmospheres, have a significant impact on crust formation because volatility increases.

② The burnability of the material affects crusting; materials that burn well tend to have lower clinker firing temperatures, reducing the likelihood of crust formation.

③ The molar ratio of sulfur trioxide to potassium oxide in the material is related to crust formation. Higher contents of volatile substances in the material increase the cohesion coefficient of the kiln system, raising the risk of crust formation.

Preventive Measures:

① Reduce or avoid using raw materials with high chlorine and sulfur contents.

② Use coal with low chlorine and low or medium sulfur content.

③ If excess chlorine and sulfur cannot be avoided:

 a. Discard part of the kiln ash to reduce the chlorine cycle.

 b. Employ a bypass air system.

④ Avoid using coal with high ash content and a low ash melting point.

⑤ Carefully operate the kiln and preheater to maintain stable temperatures, pressures, and feed quantities throughout the system.

 

Rotary Kiln

 

 

Functions of the Rotary Kiln:

The rotary kiln performs several key functions: combustion, heat exchange, chemical reactions, material transportation, degradation, and the utilization of waste.

 

Rotary Kiln System Reaction Zones:

① Drying Zone: Responsible for evaporating moisture from the raw material.

② Preheating Zone: Responsible for the decomposition and dehydration of chemically bound water in clay and other raw materials.

③ Carbonate Decomposition Zone: Mainly responsible for decomposing magnesium carbonate and calcium carbonate.

④ Exothermic Reaction Zone: Mainly responsible for solid-phase reactions that form compounds such as C2S, C4AF, and C3A, releasing heat.

⑤ Sintering Zone: Mainly responsible for the formation of C3S and the absorption of free lime (f-CaO) in the clinker.

⑥ Cooling Zone:

 a. Responsible for completing the final firing of the clinker.

 b. In this zone, clinker compounds C3A, C4AF, and a small amount of C5A3 recrystallize.

 c. Part of the liquid phase forms a glassy phase.

 d. Heat from the clinker is recovered to preheat the combustion air.