What are the advantages of high alumina bricks that cannot be achieved with clay bricks?
Al₂O₃ content greater than 48% of the aluminum silicate refractories collectively referred to as high-alumina refractories. Its stereotypical product that is the most common surge of thermal kiln high alumina bricks.
According to the amount of Al₂O₃ content, high alumina bricks can be divided into three grades:
Grade Ⅰ: Al₂O₃>75%.
Grade II: Al₂O₃60%~75%;
Grade III: Al₂O₃48%~60%.
Classified according to mineral composition as:
Low mullite and mullite (Al₂O₃48%~71.8%)
Mullite-corundum and corundum-mullite (Al₂O₃71.8%~95%);
Corundum (Al₂O₃95%~100%).
In the range of Al₂O₃ less than 71.8%, with the increase of Al₂O₃ content, the main crystalline phase mullite increases in the high-alumina products; in the range of Al₂O₃ more than 71.8%, with the increase of Al₂O₃ content, the number of mullite decreases and the number of corundum increases. The refractory properties of the products increased with the increase of Al₂O₃ content.
High alumina bricks are sintered products containing Al₂O₃ 48% or more of aluminosilicate or pure alumina. Generally, high alumina bricks contain less than 80% Al₂O₃, and those containing more than 80% Al₂O₃ are called corundum bricks.
The outstanding advantage of high alumina bricks compared with clay bricks is the high refractoriness and load softening temperature.
01.Fire resistance
The refractoriness of high alumina bricks fluctuates in a wide range, generally I770 ~ 2000 ℃, mainly affected by the content of Al₂O₃, with the increase in the content of Al₂O₃ in the products and improve. At the same time, the refractoriness is also affected by the content and type of impurities, which are related to the mineral phase structure of the products, see Table 1.

02.Load softening temperature
High alumina bricks load softening start deformation temperature is greater than 1400 ℃, and with the increase of Al₂O₃ content increases.Al₂O₃ content of less than 71.8% of the products, the load softening temperature depends on the ratio of the number of mullite and glass phases, and with the increase of the number of mullite and improve. The number and nature of the glass phase has a significant effect on the load softening point. 71.8% ~ 90% Al₂O₃ content of mullite, corundum products, with the increase in Al₂O₃ content, the amount of glass phase is basically unchanged, corundum, although there is an increase in the number of mullite, but mullite but there is a decrease in the load softening temperature; therefore, the softening temperature of the load is not significant. After Al₂O₃ content exceeds 90%, with the increase of Al₂O₃ content, the glass phase decreases, and the loading softening temperature increases significantly, from 1630 ℃ when Al₂O₃ 90% to 1900 ℃ when Alz03100%, the loading softening temperature increases with the increase of Al₂O₃ content. the relationship between the Al₂O₃ content and the loading softening temperature is shown in Fig. 1.

03. Thermal conductivity
High-alumina refractory products have higher thermal conductivity than clay products. The reason for this is that there are fewer glass phases with very low thermal conductivity in the high alumina products, while the amount of mullite and corundum crystals with better thermal conductivity increases, improving the thermal conductivity of the products. Thermal conductivity decreases with increasing temperature.
The thermal conductivity of high alumina bricks is different from that of clay and silica bricks. The thermal conductivity of high alumina bricks decreases with increasing temperature. When the higher the Al₂O₃ content in the high alumina brick, the more mullite and corundum crystals it has, the more obvious the tendency of the thermal conductivity to decrease with the increase of temperature. However, above 1000 ℃, its decrease decreases. While the thermal conductivity of both clay and silica bricks increases with increasing temperature in a linear relationship and remains unchanged near 1000℃. At room temperature, high alumina bricks than clay bricks thermal conductivity 2 ~ 3 times, but above 1000 ℃ its thermal conductivity is basically similar.
The varieties of high alumina bricks with low Al₂O₃ content are similar to clay bricks in terms of load softening point and thermal shock resistance. However, as the Al₂O₃ content increases, the load softening point and thermal shock resistance gradually increase. These characteristics of high alumina bricks make them a high-temperature type of clay bricks, so they can be used in the high-temperature parts of glass melting kilns. Varieties with low porosity can be used in high-temperature parts of heat storage chambers, such as the top of the storage chamber swan and the upper wall. The main properties of high alumina bricks are shown in Table 2.

According to the production method, there are two kinds of corundum bricks: sintered and electrofusion casting. Sintered corundum brick refractoriness up to 2000 ℃, the use of up to 1800 ℃, but its thermal expansion, and the porosity of the same mullite refractory materials, compared with its poor thermal shock resistance.

Zinfon Refractory Technology Co.,Ltd
We are a refractory material supplier integrating R&D,production,construction,warehousing and commerce.
We are offering various magnesia and alumina refractories including both shaped and unshaped products, raw materials and related chemical products.
We are certified to ISO9001, ISO14001, ISO45001 and other national and local certifications as follows:

